By Pallet wrapper | 21 June 2022 | 0 Comments
What makes the stretch film easy to break on the automatic pallet stretch wrap machine?
Fully automatic pallet stretch wrap machine, as the name implies, is a pallet packaging machine that does not require manual assistance for film application and film breaking. Compared with the semi-automatic pallet stretch wrap machine, which requires manual removal of the film, the packaging efficiency is higher, and it can also save labor costs for enterprises and reduce labor intensity for workers. But what happens if the automatic pallet stretch wrap machine often breaks the film? Next, Emanpack will take you to find out.
First, you need to observe whether the panel parameters have been adjusted. When each device is installed, professional service personnel have adjusted the parameters to suit the on-site situation. If an employee adjusts the rotation speed of the turntable or the tightening force of the turntable without authorization Parameter, it may cause film breakage problem.
Secondly, whether the stretch film used in the equipment has been replaced recently, some machine films have better tensile properties, and if they are replaced with inferior machine films, the problem of film breakage may often occur. In this case, you must first contact the professional operation personnel to adjust the parameters. If this method can ensure continuous filming, if it cannot be avoided by adjusting the parameters, you need to replace the trial machine film, try your best Membrane with satisfactory tensile properties.
Next, check the timing of film breakage. If the film falls off at the beginning of the slow start, check whether the stretch film clamped on the film breaker is too little. If it is too little, you can adjust the rope making device and the lower limit of the film seat. Let the film breaker clamp enough film; if the film is pulled off when the slow speed stop, you need to adjust the parameters of the last slow stop, so that the film will not be pulled off; finally, check whether the film is not broken. After the film holder, the stretch film is broken. You need to check the roller inside the film holder to see if its surface is smooth and without spikes. After long-term use, the film holder roller may produce some small thorns, which will be in the running process. The media was torn through a small opening causing it to break when pulled out.
Although the automatic pallet stretch wrap machine is not a very complicated equipment, various minor problems that occur during use, if you do not know how to solve it, will also seriously affect the efficiency of the factory and go against the original intention of the equipment purchase. There may be big problems hidden behind every small fault, so small faults must not be ignored.
First, you need to observe whether the panel parameters have been adjusted. When each device is installed, professional service personnel have adjusted the parameters to suit the on-site situation. If an employee adjusts the rotation speed of the turntable or the tightening force of the turntable without authorization Parameter, it may cause film breakage problem.
Secondly, whether the stretch film used in the equipment has been replaced recently, some machine films have better tensile properties, and if they are replaced with inferior machine films, the problem of film breakage may often occur. In this case, you must first contact the professional operation personnel to adjust the parameters. If this method can ensure continuous filming, if it cannot be avoided by adjusting the parameters, you need to replace the trial machine film, try your best Membrane with satisfactory tensile properties.
Next, check the timing of film breakage. If the film falls off at the beginning of the slow start, check whether the stretch film clamped on the film breaker is too little. If it is too little, you can adjust the rope making device and the lower limit of the film seat. Let the film breaker clamp enough film; if the film is pulled off when the slow speed stop, you need to adjust the parameters of the last slow stop, so that the film will not be pulled off; finally, check whether the film is not broken. After the film holder, the stretch film is broken. You need to check the roller inside the film holder to see if its surface is smooth and without spikes. After long-term use, the film holder roller may produce some small thorns, which will be in the running process. The media was torn through a small opening causing it to break when pulled out.
Although the automatic pallet stretch wrap machine is not a very complicated equipment, various minor problems that occur during use, if you do not know how to solve it, will also seriously affect the efficiency of the factory and go against the original intention of the equipment purchase. There may be big problems hidden behind every small fault, so small faults must not be ignored.
Leave a Reply
Your email address will not be published.Required fields are marked. *